READ AND KEEP THIS MANUAL FOR REFERENCE 45003A Printed in Canada
10 2.2 Installation instructions Inspect the masonry fireplace according to the safety information and fireplace requirements and have it cleaned and
11 2.4 The masonry fireplace's draft control system If the fireplace's draft control system is to remain in the masonry fireplace, it must
12 2.6 Positioning the unit In addition to ensuring compliance of the masonry fireplace hearth extension (see Compliance of the masonry fireplace in
13 If a non-combustible material floor protection needs to be added in front and level with the hearth extension masonry fireplace (see Figure 2.6a),
14 The use of an R value is convenient when more than one material is going to be used in the hearth extension to cover the combustible surface. This
15 The more extended the insert, the greater the heat transfer to the room. When installed as an extended insert, the front edge of the air jacket wi
16 Thermal characteristics of common floor protection materials* MATERIAL CONDUCTIVITY (k) PER INCH RESISTANCE (R) PER INCH THICKNESS Micore® 160 0.
17 MINIMUM MASONRY OPENING Solution 1.8-I Solution 2.3-I J 21 1/4” (540 mm) 23 3/8” (594 mm) K 28 7/8” (733 mm) 28 7/8” (733 mm) L 13 1/8” (
18 2.8 Connector installation A masonry flue connector may provide acceptable performance (Figure 2.8a); however, we recommend the use of a chimney l
19 2.8.1 Chimney liner installation To install of the chimney liner, the preferred methods are those found in Section 2.8.1.1. Use a liner offset ada
2 INTRODUCTION SBI INC., one of the most im portant wood stove and fireplac e manufacturers in Canada, congratulates you on your purchase and wishes t
20 2.8.1.2 If the chimney liner does not align with the insert’s flue outlet: You can get a liner offset adapter (AC01370), sold separately. If you m
21 2.9 Air control plate, faceplate and fan Assembly Instructions 1. Place the faceplate panels with the finished side down on a flat, soft, non-ab
22 2.10 Adapter for fresh air kit installation instructions 1- Open the rectangular outlet on the side of the unit by gently removing the materia
23 Section 3.0 Operation 3.1 Safety Information 1. This insert is designed for safe operation WHEN BURNING CORDWOOD ONLY. Altering or modifying t
24 air leakage into the unit, such as through deteriorated gaskets or cracked or broken glass. Do not operate the insert without a door gasket. Leak
25 5. Decayed wood or low density wood has very little energy content or heating value, and will not burn satisfactorily for long periods of time. A
26 4. Set the draft control at high,(see Table3.4) 5. Light a fire at the bottom of the crumpled paper and close the door. If the fire tends to go
27 3.5 Maintaining The Fire Your Enerzone insert will work best if a thick bed of hot embers is maintained in the bottom of the firebox, and a minimu
28 Section 4.0 Maintenance 4.1 Care And Cleaning Clean the insert frequently so that soot, ash and creosote do not accumulate. Do not attempt to cl
29 4.2 Ash Removal CAUTION: Ashes can start fires, even after several days of inactivity. Never dispose of ashes in a combustible container. Remov
3 TABLE OF CONTENTS INTRODUCTION ... 2Section 1.0 Pre-Installation Require
30 All firebrick and duraboard baffles must be properly in place for correct burning operation. Have any damaged firebricks replaced. Check the fireb
31 Figure 4.4.2b – Firebrick layout for 1.8-I model ITEM PIECE # DESCRIPTION QTY1 29001 4" X 8" X 1 1/4'' REFRACTORY BRIC
32 4.5 Secondary Air Tube Replacement (see Figure 4.5) 1. Remove cotter pin at RH end of tube. 2. Slide tube to left and lower tube end below RH p
33 4.6 Fan Maintenance & Care Clean the fan air inlet louvres and squirrel cage impeller regularly. The fan should be kept clean and dust free.
34 Section 5.0 Specifications 5.1 Solution 1.8-I Insert Model Fuel Type Cordwood Test Standards ULC S628 (CSA B366.2) & UL 1482 reside
35 5.2 Solution 2.3-I Insert Model Fuel Type Cordwood Test Standards ULC S628 (CSA B366.2) & UL 1482 residential. Maximum recommen
36 ENERZONE LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This
4 Section 4.0 Maintenance ... 284.1 Care And Cleaning ...
5 Solution 1.8-I Dimensions
6 Solution 2.3-I Dimensions
7 Section 1.0 Pre-Installation Requirements 1.1 Masonry & Zero Clearance Requirements The masonry fireplace must meet the minimum code requiremen
8 1.2 Venting Requirements The flue is a critical component to a satisfactory installation. Your insert will attain its best performance if installe
9 Section 2.0 Installation 2.1 Safety information NOTE: THIS APPLIANCE IS NOT RECOMMENDED FOR USE IN A HOME IF AN OCCUPANT HAS ANY RESPIRATORY OR A
Commentaires sur ces manuels